JSD-100 Manual Cinema Processor USL, Inc. 181 Bonetti Drive San Luis Obispo, CA 93401-7397 USA Phone: +1 805 549 0161 F
Page 10 GUI. Similarly, individual Ls/Rs output delays are also available in the crossover section where multiple Ls/Rs outputs are available. See t
Page 11 The bottom section of figure 4.2a shows what a typical analog output looks like. The appropriate DSP drives a digital to analog converter, w
Page 12
Page 13 4.3 Model Numbers The output module is field replaceable to allow a variety of output configurations. Available output configurations incl
Page 14 5.1LsCL RRs7.1SDDSLc Rc7.1DSLrs RrsLFECL RLFECL RLFELs RsLs RsRight surround (Rs) Typically an array of loudspeakers positioned along the ri
Page 15 Inputs Processing Channel Output Panel Identifier AES 1, Analog 1, Stereo, Mic Left L AES 2, Analog 2, Stereo, Mic Right R AES 3, Analog 3,
Page 16 Communication Ports DB25F pulse automation. Serial control – RS-232. USB for laptop setup. Ethernet 10/100 - RJ45. Front Panel Inte
Page 17 Internal crossovers on systems with 16 or more outputs. Crossovers support biamp and triamp of up to five screen channels plus individual
Page 18 permits. Mounting the unit immediately above a major heat-producing component, such as a power amplifier, is not recommended. Equipment
Page 19 16. 8 Channel Analog Input on DB25F – Balanced line inputs. Six channels are fixed (L, C, R, LFE, Ls, Rs) and two can be set up as either
Page 2 One-Year Limited Warranty USL, Inc. warrants that each product manufactured by it will be free from defects in material and workmanship un
Page 20 6.5 Thirty-two Channel AES Output Rear Panel Connections (JSD-100xD) A set of clip-on ferrite “beads” is supplied with the JSD-100. To E
Page 21 6.6 Audio Input Connections 8/16 Channel AES Input The JSD-100 accepts 16 channel AES audio if the optional DI-80 card is installed. Othe
Page 22 6.7 Analog Audio Output Connections Depending on which analog output module is installed, the JSD-100 provides eight or sixteen main channe
Page 23 Ethernet Interface The JSD-100 includes a standard 10/100Mbps Ethernet interface. The same automation commands (described in Appendix B) ar
Page 24 USB Driver Removal To remove the previous JSD-100 USB driver installation, the JSD-100 must be connected to the computer and by usin
Page 25 7.3 Set IP Utility The Set IP utility allows the user to configure the network settings on the JSD-100. Connect the host computer to
Page 26 Open. Pressing “Open” allows you to load an existing configuration fie. Use Default.j100 to load the factory defaults. You can then rev
Page 27 auditorium. Note that crossovers and 13.1 will not be available on systems with the 8 channel output card. On these 8 channel outpu
Page 28 The other sections of this screen cannot be changed through the summary tab. Theater Information The data in the theater information field
Page 29 Preset Level If preset is enabled, the JSD-100 will adjust the main fader level to the preset level set here. If the preset is not enabled,
Page 3 Table of Contents 1. Safety Notice 5 2. Regulatory Compliance 5 2.1 Declaration of Conformity
Page 30 Decode Option Description L_R The two channel source drives just the left and right speakers. L_C_R The left and right channels of the sour
Page 31 provides a faster update, but a less stable display. As you close in on the final adjustment of the equalizer, increase the decay time towar
Page 32 11. Smooth equalizer settings to avoid large transitions between adjacent bands while keeping RTA data within limits. 12. Adjust output tr
Page 33 Unit Time The time settings in the unit can be observed in this section of the tab. The Unit Time data includes the current UTC value in t
Page 34 Sleep Settings The JSD-100 includes a sleep timer. The timer is reset to its timeout value on any format change, any fader level change, or
Page 35 The Speaker button opens a file select dialog where you can select a speaker from the speaker library. This loads all the crossover settings
Page 36 The log shows the record number in the JSD-100 log, the UTC time of the event, the “JSD Time” of the event, and the “GUI Time” of the event.
Page 37 7.5 Channel Crossover and Equalization Procedure Audio channel equalization consists of two steps: 1. Crossover adjustment (if crossove
Page 38 19. Use the rear panel trim pots to adjust the low, mid, and high band gains as required for a relatively flat response
Page 39 d. Press the Flatten button. e. Press Pink and Generator to drive the center channel with pink noise. f. Adjust the main fader towards 7.
Page 4 7.5.2.1 Automatic Equalization 38 7.5.2.2 Manual Equalization 38 7.5.2.3 LFE Equalization Procedure
Page 40 4. Adjust the frequency control to the worst dip or peak in the LFE portion of the RTA display. 5. Set the Q to 4 and adjust the PEQ gain
Page 41 8. System Operation The JSD-100 is controlled by the digital cinema server in most installations. Control is also available from the front
Page 42 will change to that level when the format is selected. If the format does not have a preset fader level, the fader will change to the l
Page 43 Adding Auditoriums Click the “Auditoriums” button. The Add Auditorium dialog box will appear. Click “Add” to add an auditorium. The
Page 44 The Configuration Page shows the same auditorium data and network data as the status page. When first accessing the configuration page
Page 45 C:>snmpwalk -v 1 -c public 192.168.1.159 iso SNMPv2-MIB::sysDescr.0 = STRING: digital cinema sound processor SNMPv2-MIB::sysObjectID.0 =
Page 46 SNMPv2-SMI::enterprises.38012.4.5.2.23 = INTEGER: 23 SNMPv2-SMI::enterprises.38012.4.5.2.24 = INTEGER: 24 SNMPv2-SMI::enterprises.38012.4.5.
Page 47 8. JSDV-100 Remote Volume Control The JSDV-100 remote volume control can be installed in an auditorium or other location. It is wired to
Page 48 10. Product Support USL proudly stands behind its products. We are ready to answer questions about the installation or operation of the
Page 49 Appendix A – Connector Pin Outs Connector Pin Outs For convenience, all connector pin outs are located in this appendix. DB25F AES Input.
Page 5 1. Safety Notice Safety Notices Review the following safety precautions to avoid injury and prevent damage to this product. To avoid p
Page 50 Channel Number DB25F PINS ( +, -, shield ) Speakers 1 2, 14, 1 Left 2 8, 20, 7 Right 3 5, 17, 4 Center 4 25, 12, 13 LFE 5 23, 10, 22 Ls 6 24
Page 51 Full Range Audio Channel Biamp Audio Channel Triamp Audio Channel Phoenix Main Output Pins (+, -, shield) DB25M Monitor 1 Output Pins (+, -,
Page 52 Full Range Cable Pair 5.1 7.1 DS 7.1 SDDS 13.1 1-1 L/R L/R L/R L/R 1-2 C/LFE1 C/LFE1 C/LFE1 C/LFE1 1-3 Ls/Rs Ls/Rs Ls/Rs Ls/Rs 1-4 Not Used
Page 53 Control/Monitor RJ45 The AES output module uses an RJ45 connector for control and monitoring. The control function is the USL-Link supported
Page 54 Pin Description 1 Control 1. Pulse low to select format 1 (COAX1). Pulses low when format 1 selected. 2 Control 2. Pulse low to select fo
Page 55 USL Link The USL Link is an RS485 bus used to interface the JSD-100 to other USL devices such as the JSDV-100 remote volume contr
Page 56 Appendix B – Automation Commands These commands are used to query the status of the JSD-100 or change its operation (adjust level, select i
Page 57 jsd100.sys.mute\t1\r 1 Sets or reads the current mute status of the JSD-100. If the supplied parameter is 1, the system is muted. If the su
Page 58 Appendix C – System Restore and Power-Up Buttons System Restore The JSD-100 has several methods of recovering from an unlikely failure. The
Page 59 Appendix D – JSD-100 Accessories AES RJ45 Adapters for various servers The JSD-100 can use CAT5 cable with RJ45 connectors to carry AES au
Page 6 Évitez l’Ensemble de circuits Exposé. N’entreprenez pas ouvrir la Provision du Pouvoir parce que sa certi-fication de la séc
Page 60 Appendix E – INI File Formats Many configuration files used by the JSD-100 GUI are plain text ini files. They are located in My Documents\U
Page 61 # After automatic EQ setting, the bands can then be offset to move them all # up or down (whole set). # OffsetEQBands - When set to a one, o
Page 62 Band12500=1 Band16000=1 Treble=1 # The bass and teble are a shelving filter that are adjusted prior to # the individual equalizer bands. Tha
Page 63 Max=3 Min=-3 [Band200Hz] Value=0 Max=3 Min=-3 [Band250Hz] Value=0 Max=3 Min=-3 [Band315Hz] Value=0 Max=3 Min=-3 [Band400Hz] Value=0 Max=3 Mi
Page 64 Min=-5 [Band4kHz] Value=-2.5 Max=0.5 Min=-5.5 [Band5kHz] Value=-3.5 Max=-0.5 Min=-6.5 [Band6.3kHz] Value=-4.5 Max=-1.5 Min=-7.5 [Band8kHz] V
Page 65 Band40=0.0 Band50=0.0 Band63=0.0 Band80=0.0 Band100=0.0 Band125=0.0 Band160=0.0 Band200=0.0 Band250=0.0 Band315=0.0 Band400=0.0 Band500=0.0
Page 66 PEQ1Freq=800 PEQ1Q=1.0 PEQ1Gain=0.0 PEQ2Freq=6000 PEQ2Q=1.0 PEQ2Gain=0.0 [High Band] HPFreq=1400 Gain=-5.0 Delay=0.0 PEQ1Freq=4000 PEQ1Q=
Page 67 JSD-100 Manual Revision History 1. April 2010 – First Edition (preliminary). 2. October 2010 – Second Edition. 3. July 12, 2011 – Adds su
Page 68 JSD-100x JSD-100xA JSD-100xD Additional JSD-100 Manuals may be viewed / downloaded at: www.uslinc.com
Page 7 Stellen Sie Richtige Belüftung bereit. Die operierend Temperatur sollte zwischen 0° C und 40° C. Die Luftfeuchtigkeit sollte
Page 8 VDE Certified Power Cords. Pollution: Not intended for environments where conductive pollutants may be present. 2.2 Equipment Class
Page 9 The JSD-100 is “automation friendly.” It features the standard DB25 parallel automation interface, an RS-232 (EIA232) interfa
Commentaires sur ces manuels