Usl JSD-100 Manuel d'installation

Naviguer en ligne ou télécharger Manuel d'installation pour Processeurs Usl JSD-100. Usl JSD-100 Installation manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer

Résumé du contenu

Page 1

GDC Technology Ltd SX-2000 SERVER INSTALLATION MANUAL

Page 2 - Table of Contents

SX-2000 Installation Manual 11/8/2010 GDC Technology Ltd. Page 9 of 42 Figure 10 Inserting the IMB into the projector Insert the IMB as shown

Page 3

SX-2000 Installation Manual 11/8/2010 GDC Technology Ltd. Page 10 of 42 2.5.2.1 Connecting to the IMB and the projector Connect the PCI-e cab

Page 4 - 2.1 Server Presentation

SX-2000 Installation Manual 11/8/2010 GDC Technology Ltd. Page 11 of 42 2.5.3 Series 2 projector setup To work with the GDC IMB, the projector

Page 5 - 2.3 Insertion of Drives

SX-2000 Installation Manual 11/8/2010 GDC Technology Ltd. Page 12 of 42 3. Select [Start] ->[Mode] ->[Service] and enter the Service pas

Page 6 - 2.4 Cable connections

SX-2000 Installation Manual 11/8/2010 GDC Technology Ltd. Page 13 of 42 5. Select [Start] ->[Power] ->[On] to power on the projector. 6

Page 7 - 2.5.1.1 IMB components

SX-2000 Installation Manual 11/8/2010 GDC Technology Ltd. Page 14 of 42 b. Read and perform the actions listed in the Marriage Checklist. In

Page 8

SX-2000 Installation Manual 11/8/2010 GDC Technology Ltd. Page 15 of 42 Figure 18 Arm Marriage and Marriage countdown d. The Finish window st

Page 9

SX-2000 Installation Manual 11/8/2010 GDC Technology Ltd. Page 16 of 42 All 3D IMB channels on the Christie Series 2 projector should use the

Page 10 - SX-2000 Installation Manual

SX-2000 Installation Manual 11/8/2010 GDC Technology Ltd. Page 17 of 42 Figure 20 3D macro settings for Christie projectors The settings for 3

Page 11

SX-2000 Installation Manual 11/8/2010 GDC Technology Ltd. Page 18 of 42 Figure 21 IMB 3D 4:4:4 configuration on SX-2000 server 2.6.1.1 NEC Se

Page 12

SX-2000 Installation Manual 11/8/2010 GDC Technology Ltd. Page 1 of 42 Table of Contents 1 Introduction ...

Page 13

SX-2000 Installation Manual 11/8/2010 GDC Technology Ltd. Page 19 of 42 3.1 SX-2000 configuration 3.1.1 Server IP Setup The IP address of the

Page 14

SX-2000 Installation Manual 11/8/2010 GDC Technology Ltd. Page 20 of 42 8 Click [Restart network service] on the Admin Panel Page to restart t

Page 15

SX-2000 Installation Manual 11/8/2010 GDC Technology Ltd. Page 21 of 42 Figure 24 Cinecanvas setup screen 5 Enter the projector IP address in

Page 16

SX-2000 Installation Manual 11/8/2010 GDC Technology Ltd. Page 22 of 42 3.1.3.1 Content ingest from USB disk The following steps describe the

Page 17

SX-2000 Installation Manual 11/8/2010 GDC Technology Ltd. Page 23 of 42 Figure 27 USB ingest source setup 5. Click [Save] to save the setting

Page 18

SX-2000 Installation Manual 11/8/2010 GDC Technology Ltd. Page 24 of 42 3. Enter the respective parameters for Source IP, Source Path, Usernam

Page 19

SX-2000 Installation Manual 11/8/2010 GDC Technology Ltd. Page 25 of 42 3.1.3.3 Selecting an ingest source To select an ingest source, click

Page 20 - 3.1.1 Server IP Setup

SX-2000 Installation Manual 11/8/2010 GDC Technology Ltd. Page 26 of 42 3.1.4 Time Zone Setup The SX-2000 server may or may not arrive with th

Page 21

SX-2000 Installation Manual 11/8/2010 GDC Technology Ltd. Page 27 of 42 3.2 Audio Setup Not every case will require a Digital-to-Analog Conve

Page 22

SX-2000 Installation Manual 11/8/2010 GDC Technology Ltd. Page 28 of 42 2. Connect the other end of the audio cable into the input labeled “4x

Page 23

SX-2000 Installation Manual 11/8/2010 GDC Technology Ltd. Page 2 of 42 3.3.7 Automation setup for Christie ACT devices ...

Page 24

SX-2000 Installation Manual 11/8/2010 GDC Technology Ltd. Page 29 of 42 3.3 Automation Setup The SX-2000 server is able to control external d

Page 25

SX-2000 Installation Manual 11/8/2010 GDC Technology Ltd. Page 30 of 42 3.3.2 Adding event labels and actions The following steps describe how

Page 26

SX-2000 Installation Manual 11/8/2010 GDC Technology Ltd. Page 31 of 42 3.3.3 Automation Scheduling Automation event labels can be scheduled t

Page 27 - 3.1.4 Time Zone Setup

SX-2000 Installation Manual 11/8/2010 GDC Technology Ltd. Page 32 of 42 Figure 33 GPIO automation device settings If the output pulse width is

Page 28 - 3.2.3 USL DAX-602

SX-2000 Installation Manual 11/8/2010 GDC Technology Ltd. Page 33 of 42 Figure 34 Projector automation device setup Figure 35 Automation sett

Page 29

SX-2000 Installation Manual 11/8/2010 GDC Technology Ltd. Page 34 of 42 Figure 36 eCNA automation device setup 8. Click [OK] and set up the d

Page 30 - 3.3 Automation Setup

SX-2000 Installation Manual 11/8/2010 GDC Technology Ltd. Page 35 of 42 3.3.7 Automation setup for JNIOR devices The SX-2000 server supports th

Page 31

SX-2000 Installation Manual 11/8/2010 GDC Technology Ltd. Page 36 of 42 Figure 39 Automation settings for JNIOR device 3.3.8 Automation setup

Page 32 - 3.3.3 Automation Scheduling

SX-2000 Installation Manual 11/8/2010 GDC Technology Ltd. Page 37 of 42 Figure 40 Christie ACT automation device setup Figure 41 Automation s

Page 33

SX-2000 Installation Manual 11/8/2010 GDC Technology Ltd. Page 38 of 42 5. Click the [Save] button to save configured settings. Figure 42 Dol

Page 34

SX-2000 Installation Manual 11/8/2010 GDC Technology Ltd. Page 3 of 42 1 Introduction This document is a guide through the process of setting

Page 35

SX-2000 Installation Manual 11/8/2010 GDC Technology Ltd. Page 39 of 42 3. Enter the IP address of the USL DAX device (see Figure 45). 4. Cl

Page 36

SX-2000 Installation Manual 11/8/2010 GDC Technology Ltd. Page 40 of 42 3. Enter the IP address of the USL JSD device (see Figure 47). 4. Sel

Page 37

SX-2000 Installation Manual 11/8/2010 GDC Technology Ltd. Page 41 of 42 Figure 48 Component Engineering TA-10 wiring diagram 3.4 Testing Pro

Page 38

SX-2000 Installation Manual 11/8/2010 GDC Technology Ltd. Page 4 of 42 Figure 3 SX-2000 server with external touchscreen LCD 2.2 Placing the

Page 39

SX-2000 Installation Manual 11/8/2010 GDC Technology Ltd. Page 5 of 42 4 Insert each drive into the hot swap bay while making sure that the gr

Page 40

SX-2000 Installation Manual 11/8/2010 GDC Technology Ltd. Page 6 of 42 2.5 Installing and connecting the GDC Integrated Media Block (IMB) I

Page 41

SX-2000 Installation Manual 11/8/2010 GDC Technology Ltd. Page 7 of 42 Figure 6 GDC Integrated Media Block (IMB) 2.5.1.2 Remove existing int

Page 42

SX-2000 Installation Manual 11/8/2010 GDC Technology Ltd. Page 8 of 42 Figure 8 IMB placement on Christie projectors Figure 9 shows the locati

Commentaires sur ces manuels

Pas de commentaire